Test & Measurement
Part Number:6200-040 / 6200-042/ 6200-030 / 6200-032
Item No:HKC808
The Nova-Strobe series represents the latest in portable stroboscope technology. Both the AA and AB are simple to operate, just point and shoot. Lightweight and bright with flash rates to 8,000 flashes per minute these strobes are comfortable to hold and will operate continuously with no danger of overheating. The AB battery operated stroboscope weighs only 2.5 lbs. (1.2kg) and will run continuously for 1 hour on a single charge. A slow charger is included. The AA stroboscope is AC mains powered (115 or 230 Vac) and weighs only 1.5 lbs. (0.72 kg). A large easy to read drum with clear numeric markings makes it easy to adjust and read the flash rate.
Part Number:Fluke VR101S
Item No:HKC807
Set up, plug in, download, and analyze Homes, offices, hospitals, and factories depend on electronic devices. And electronic devices depend on good power quality. The Fluke VR101S is the perfect system for catching sags, swells, transients, outages and frequency variations on line voltage at receptacles, where the most sensitive loads are connected. The VR101S is a starter system that includes a compact VR101 event recorder, an optical interface cable, and EventView software that turns your PC into a power quality reporting tool. Additional VR101 event recorders can be purchased individually, so you can monitor several voltage conditions at multiple locations at once. EventViewTM version 2.11 allows you to set event capture limit parameters for the VR101 Voltage Event Recorder, and download the captured event data into your PC for analysis. If you have EventView software with a version number lower than 2.10, it may not be compatible with the most recent versions of the VR101 Voltage Event Recorder, so it is suggested that you upgrade your software.
Part Number:Fluke VoltAlert 1AC/ 1 LAC
Item No:HKC806
Easy-To-Use Voltage Detectors VoltAlert ac voltage testers from Fluke are easy to use-just touch the tip to a terminal strip, outlet, or cord. When the tip glows red, you know there's voltage in the line. Electricians, maintenance, service, safety personnel, and homeowners can quickly test for energized circuits and defective grounds on the factory floor, in the shop, or at home. Now available in two voltage ranges The new VoltAlert 1LAC is for detecting control voltage from 24V ac to 90V ac. The VoltAlert 1AC is for detecting line voltage from 90V ac to 600V ac. The 1LAC is not available in Europe or Australia. The 1AC is not available in Australia or Sweden.
Part Number:Fluke T5
Item No:HKC805
Electrical tester with OpenJaw?Current The Fluke T5 Electrical Testers let you check voltage, continuity and current with one compact tool. With the T5, all you have to do is select volts, ohms, or current and the tester does the rest. OpenJaw?current lets you check current up to 100A - without breaking the circuit. Its tough test leads stow neatly in the back of the tester, making it easy to tote the T5 in your tool pouch. Detachable SlimReach?test probes are customized for national electrical standards. The test leads accept optional accessories such as clips and specialty probes. The optional H5 holster lets you clip the T5 onto your belt. Available in 600V and 1000V models. Features Automatically measures volts ac and volts dc with precise digital resolution Displays resistance to 1000W Easy and accurate OpenJaw?current measurement Continuity beeper Compact design with neat probe storage Rugged enough to withstand a 10-foot (3m) drop Detachable SlimReach?probe tips are customized for national electrical standards Test leads accept Fluke accessory test clips Available in 600V and 1000V models Can stay connected much longer than solenoid type tester Auto off mode to conserve battery life Optional holster attaches to a belt and neatly stows test leads
Part Number:Fluke T2
Item No:HKC804
Now You Can Get More From a Tester The Fluke T2 is a voltage and continuity tester that's designed to work long and hard. There are no settings_just probe the circuit and the T2 will show you whether you're looking at ac volts, dc volts, or an open circuit. You don't even have to turn it on or off! With seven different voltage indicators, it can clearly differentiate between key voltage levels. Features LEDs clearly indicate seven ac and seven dc nominal voltage levels Indicates dc voltages as low as 6V DC polarity indicator Compact and rugged_fits in a tool pouch or overall pocket Automatically selects continuity beeper or voltage measurement Can stay connected much longer than solenoid type testers Rugged enough to withstand a 10-foot (3m) drop Protected to 1000V input, for use in CAT III environments Automatically activates and shuts down to conserve battery power Heavy-duty test leads for long life
Part Number:Fluke 7-300 / 7-600
Item No:HKC803
Put Electrical Tests on Automatic The 7 Series testers are designed for safe, automatic measurements of ac volts, dc volts, resistance and continuity. Simply turn on and use. Auto Selection simplifies voltage measurements in power environments. When measuring ohms/continuity with more than 4.5 volts present across the input jacks (intentional or not) the meter automatically switches to measuring ac or dc volts, whichever is greater. Input impedance is approximately 2kOhms, helping determine if voltage is from leakage (so-called "ghost" voltages) or a hard connection. Overload protection is provided in all measurement
Part Number:ET34
Item No:HKC802
Bright indicating LEDs at 12, 24, 120, 208, 240, 277 and 480V 6111448416Audible and Visible continuity test up to 200k 6111448416Single pole live voltage detector 6111448416Voltage function operates without batteries 6111448416Automatic AC/DC indication plus DC polarity 6111448416Meets IEC 1010, CAT III 6111448416Complete with 39" (1m) cable with test lead and two 1.5V AAA batteries
Part Number:380400 /380405
Item No:HKC801
Wide range decade boxes for product design or calibration checks 1% Resistance substitution to 110Ohms and 5% Capacitance substitution to 11,111µF . High impact case may be grounded separately. Three binding posts permit isolated substitutions. Light heavy duty durable construction Seperate grounding terminal Three binding posts permit isolated substitutions Dimensions: 4.6x5.7x1.4" (116.8x144.8x35.6mm) Weight: 0.66lbs (299g) Model 380400 Resistance Box Features: E 1% Resistance substitution from 1 to 11, 111, 110 E Seven Decade Ranges of Resistance E Values can be changed in 1 increments E 0.3W resistors E 0.3 internal zero resistance Model 380405 Capacitance Box Features: • 5% Capacitance substitution from 100pF to 11, 111µF • Excellent for circuit development • Five Decade Ranges of Capacitance • Capacitor rated to 50VDC • 50pF internal zero capacitance
Part Number:380193
Item No:HKC800
Measures Capacitance and Inductance to 0.7% and Resistance to 0.5% 6111448416Simultaneous 20,000/10,000 count display of the primary parameter (L, C or R) with the secondary parameter of Q (quality), D (dissipation) or R (resistance) 6111448416Test frequencies of 120Hz and 1kHz 6111448416Set Hi/Lo limits using absolute values or percentage limits 6111448416Selectable Parallel or Series equivalent circuit 61114484164-1/2 digit backlit LCD display provides resolution to 0.1pF, 0.16131339496 and 0.001 6111448416Max/Min/Avg recording 6111448416Built-in test fixture or use external test leads 6111448416Open and Short Zero removes unwanted stray impedances from the measurement 6111448416Relative mode with zero reference or user supplied reference 6111448416Auto power off 6111448416Automatic blown fuse indication 6111448416Powered by 9V battery or optional AC adaptor 6111448416Complete with test leads, alligator clips, 9V battery, and protective holster
Part Number:DVA30
Item No:HKC799
The only two-in-one current/voltage detector designed for electrical testing Non-Contact AC voltage detection from 5V to 250VAC Non-Contact AC current detection from 400mA Sensitivity adjustments to increase or reduce sensor trigger threshold Loud audible and bright visible sense detect indicators Current sensor detects current flow through shielded wires, conduit and metal circuit breaker/junction boxes Current function detects current flow of 400mA at 0.2" distance and at much greater distances for larger current flows Convenient pocket size with clip Dimensions/Wt: 7.6x1.2x0.9" (192x31x24mm) / 2.1oz (60g) Complete with four LR44 button batteries and pocket clip
